LAYERCALIBER

ELEGOO Saturn 3 Ultra resin exposure settings

ELEGOO publishes starting settings for 21 resins on the ELEGOO Saturn 3 Ultra, covering 273 colour settings. This page lists every one exactly as published on the ELEGOO Wiki (checked 23 October 2026), grouped by resin. Each value is a starting point: confirm it with a calibration print before relying on it.

Starting settings only, transcribed from the source. LayerCaliber has not physically print-tested them. Confirm with a calibration print and follow your printer and resin manufacturers' instructions.

Summary

Resins listed21
Colour settings273
Layer height50 µm and 100 µm
Print modesNormal resin + normal speed · Normal resin + fast printing · Fast resin + fast printing
Rest after retract0 s / 1 s
Bottom layersNot published by the source
Lift / retract3 different sets (see tables)

ELEGOO lists separate settings for each print mode on this printer. The tables below are grouped by mode; each mode has its own layer height.

Listed by ELEGOO as: Saturn 3 Ultra(fast resin+fast printing), Saturn 3 Ultra(normal resin+fast printing), Saturn 3 Ultra(normal resin+normal speed). Bottom layer count and transition layers are not published by this source.

Open any row in the calculator to copy, share or print it, and to record your own calibrated values.

Where to buy

Affiliate links: the Amazon links on this page are search links. As an Amazon Associate, LayerCaliber earns from qualifying purchases. They do not affect any setting shown, and LayerCaliber has not tested these products. Affiliate disclosure

Search Amazon for the ELEGOO Saturn 3 UltraAffiliate link

Settings by resin

ELEGOO Standard Resin 1.0

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Standard Resin 1.0 on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Clear Red, Clear Green, Clear Blue, Blue, Yellow, Beige2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black, Translucent, Maroon3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Standard Resin 1.0 on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Clear Red, Clear Green, Clear Blue, Blue, Yellow, Beige3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black, Translucent, Maroon4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Standard Resin 1.0Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO Standard Resin 2.0

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Standard Resin 2.0 on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Orchid, Slate Blue, Medium Slate Blue3.5–4 s35–40 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Standard Resin 2.0 on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Orchid, Slate Blue, Medium Slate Blue3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Standard Resin 2.0Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Resin 1.0

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Resin 1.0 on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Clear Red, Clear Green, Clear Blue, Blue, Yellow, Beige, Mint Green, Smoky Black2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black, Maroon3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Clear6–8 s35–40 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Resin 1.0 on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Clear Red, Clear Green, Clear Blue, Blue, Yellow, Beige, Mint Green, Smoky Black3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black, Maroon4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Clear10–12 s45–50 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Resin 1.0Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Resin 2.0

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Resin 2.0 on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Resin 2.0 on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Resin 2.0Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Resin 3.0

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Resin 3.0 on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Clear Red, Clear Green, Translucent, Mint Green, Yellow, Smoky Black, Beige, White, Clear Blue, Blue2.8–3.2 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Resin 3.0 on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Clear Red, Clear Green, Translucent, Mint Green, Yellow, Smoky Black, Beige, White, Clear Blue, Blue3.8–4.5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Resin 3.0Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Resin 3.0 +

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Resin 3.0 + on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Clear Red, Clear Green, Translucent, Mint Green, Yellow, Smoky Black, Beige, White, Clear Blue, Blue2.8–3.2 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Resin 3.0 + on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Clear Red, Clear Green, Translucent, Mint Green, Yellow, Smoky Black, Beige, White, Clear Blue, Blue3.8–4.5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Resin 3.0 +Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Resin 3.0 Pro

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Resin 3.0 Pro on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Beige, Clear Green, Yellow2.8–3.2 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black, Translucent3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Resin 3.0 Pro on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Beige, Clear Green, Yellow3.8–4.5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black, Translucent4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Resin 3.0 ProAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO Water Washable Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Water Washable Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Ceramic Grey, White, Clear Red, Clear Green, Clear Blue, Yellow, Beige, Mint Green, Smoky Black2.5–3 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Water Washable Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Ceramic Grey, White, Clear Red, Clear Green, Clear Blue, Yellow, Beige, Mint Green, Smoky Black3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Water Washable ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO Water Washable 2.0 Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Water Washable 2.0 Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Ceramic Grey, White, Clear Red, Clear Green, Clear Blue, Yellow, Beige, Mint Green, Smoky Black, Blue2.5–3 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Water Washable 2.0 Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Ceramic Grey, White, Clear Red, Clear Green, Clear Blue, Yellow, Beige, Mint Green, Smoky Black, Blue3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Water Washable 2.0 ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO Water Washable ABS-Like Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Water Washable ABS-Like Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Ceramic Grey, White, Clear Red, Clear Green, Smoky Black, Clear Blue, Yellow, Beige, Mint Green, Blue2.8–3.2 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Water Washable ABS-Like Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Ceramic Grey, White, Clear Red, Clear Green, Smoky Black, Clear Blue, Yellow, Beige, Mint Green, Blue3.8–4.2 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.2–4.8 s40–45 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Water Washable ABS-Like ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO Standard Plant-based Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Standard Plant-based Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Clear Green, Translucent2.5–3 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Standard Plant-based Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Clear Green3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black, Translucent4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Standard Plant-based Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Plant-based Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Plant-based Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Clear Green2.5–3 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator
Black3–3.5 s30–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Plant-based Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Clear Green3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator
Black4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Plant-based Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO 8K Water Washable Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO 8K Water Washable Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Vanilla, White Smoke2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO 8K Water Washable Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke4–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO 8K Water Washable Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO 8K Standard Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO 8K Standard Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, Vanilla, White Smoke2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO 8K Standard Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, Vanilla, White Smoke4–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO 8K Standard Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO 8K ABS-Like 3.0 Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO 8K ABS-Like 3.0 Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke, Vanilla2.5–3 s25–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO 8K ABS-Like 3.0 Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke, Vanilla4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO 8K ABS-Like 3.0 Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO 8K Water Washable ABS-Like Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO 8K Water Washable ABS-Like Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke, Vanilla2.5–3 s25–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO 8K Water Washable ABS-Like Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke, Vanilla4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO 8K Water Washable ABS-Like Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO 8K Water Washable 2.0 Photopolymer Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO 8K Water Washable 2.0 Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke, Vanilla2.5–3 s25–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO 8K Water Washable 2.0 Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Space Grey, Red Clay, White Smoke, Vanilla4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO 8K Water Washable 2.0 Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO ABS-Like Ultra Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO ABS-Like Ultra Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Black, Beige, Yellow, Clear Blue, Clear Red, Clear Green, Neon-Pumpkin, Neon-Lemon, Neon-Lime, Neon-Peach2.5–3.5 s25–35 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO ABS-Like Ultra Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, White, Black, Beige, Yellow, Clear Blue, Clear Red, Clear Green, Neon-Pumpkin, Neon-Lemon, Neon-Lime, Neon-Peach4.5–5 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO ABS-Like Ultra ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO Tough Resin 1.0

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Tough Resin 1.0 on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Black2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Tough Resin 1.0 on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey, Black3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Tough Resin 1.0Affiliate link · Check the listing matches the exact resin and colour.

ELEGOO Thermochromic Resin

Normal resin + normal speed · 50 µm

ELEGOO note: This parameter works for Normal Resin + Normal Speed

ELEGOO Thermochromic Resin on the ELEGOO Saturn 3 Ultra, Normal resin + normal speed. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 50 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey To Purple2.5–3 s25–30 s1 s3+4 mm at 90+320 mm/min; retract 320+90 mm/minOpen in calculator

Normal resin + fast printing · 100 µm

ELEGOO note: This parameter works for Normal Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Thermochromic Resin on the ELEGOO Saturn 3 Ultra, Normal resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey To Purple3.5–4 s35–40 s1 s3+2 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Thermochromic ResinAffiliate link · Check the listing matches the exact resin and colour.

ELEGOO Rapid Standard Photopolymer Resin

Fast resin + fast printing · 100 µm

ELEGOO note: This parameter works for Fast Resin+ Fast Speed (Hollow model, wall thickness>2mm, model has holes)

ELEGOO Rapid Standard Photopolymer Resin on the ELEGOO Saturn 3 Ultra, Fast resin + fast printing. Source: ELEGOO Wiki: ELEGOO Resin Settings, checked 23 October 2026. Layer height 100 µm.
ColoursNormal exposureBottom exposureRest after retractLift / retractCalculator
Grey1.8 s30–40 s0 s2+1 mm at 300+1000 mm/min; retract 1000+300 mm/minOpen in calculator

Search Amazon for ELEGOO Rapid Standard Photopolymer ResinAffiliate link · Check the listing matches the exact resin and colour.

Using these settings

  1. Pick the row for your exact resin and colour. Do not transfer values to other printers, resins or colours.
  2. Where a range is given, start inside it.
  3. Run a calibration print from its original creator (see calibration tests) and adjust according to their instructions.
  4. Record what worked in the calculator's "Record your calibrated values" panel so it is included when you copy or print your settings.

Other Saturn printers

All printers