LAYERCALIBER

Resin 3D Printing Exposure Calculator

Look up manufacturer-published starting settings for a specific MSLA printer and resin, see where each value comes from, and record what your own calibration prints confirm. Covers 22 printers and 2,967 published colour settings from ELEGOO and Siraya Tech.

Starting settings only. Confirm with a calibration print and follow your printer and resin manufacturers' instructions.

Printer & resin

How to use this tool
  1. Choose a supported printer and resin combination.
  2. Check the profile's layer height, and its print mode or temperature condition where the source lists one.
  3. Review the starting settings and their source.
  4. Run a suitable calibration print ().
  5. Adjust according to the test creator's instructions and record the result below.
Printer

Exact model. Settings for one printer are not transferred to another.

Resin

Only resins with a published profile for the selected printer are listed.

Temperature condition

Colour

Pigment changes how light is absorbed, so colours can have different settings.

Layer height

Fixed by the source profile. Other layer heights are not extrapolated.

Starting settings

Record your calibrated values User-entered

Saved only in this browser. Included when you copy or print settings.

Reference tables

Every profile this site uses, exactly as published by its source. Ranges are shown as published; nothing here is calculated. "Not published" means the source does not state a value.

Sources last checked 23 October 2026 (ELEGOO Wiki) and 22 October 2026 (Siraya Tech). Values are transcribed from manufacturer sources; none has been physically print-validated by LayerCaliber. Check the source before printing; manufacturers update settings.
PrinterResinColoursMode / conditionLayerNormalBottomBottom layersRest after retractLift / retractSourceAction

Learn

Why settings are printer- and resin-specific

Cure depth depends on the light dose reaching the resin, and on how that resin absorbs light. Light-source power, optics, release film, resin formulation and pigment all differ, so a value published for one printer, resin or colour does not carry over to another. That is why this tool only shows exact published combinations.

Slicer terms used here

  • Normal exposure: UV-on time for each regular layer.
  • Bottom exposure / bottom layers: longer exposure for the first layers so the part adheres to the build plate.
  • Transition layers: layers that step from bottom to normal exposure. Not every slicer has them.
  • Rest time after retract: a wait after the plate returns, before exposure. ELEGOO lists this setting. It is not the same as a "light-off delay", which some slicers time from a different point; check your slicer's definition.

Lift and retract motion

Some printers support two-stage motion (a slow first stage while the layer separates from the film, then a faster stage). Values are shown only when the source publishes them for that printer. Some printers use other release mechanisms. Where ELEGOO lists no lift values ("/"), the calculator shows them as not published.

Temperature

Resin viscosity and reactivity change with temperature. Siraya Tech publishes separate Blu settings for 25–35 °C resin and 20–28 °C room temperature. The ELEGOO profiles here do not state a temperature, so check the resin's own instructions.

Methodology

How profiles are chosen, what is and isn't calculated, and known limitations.

Safety

Uncured resin and used solvent need careful handling. Follow the Safety Data Sheet (SDS) for your exact resin.

Related equipment

Affiliate links: the links below are Amazon search links. As an Amazon Associate, LayerCaliber earns from qualifying purchases. These links are separate from the calculator: they do not affect any setting shown, and LayerCaliber has not tested these products.

As an Amazon Associate, LayerCaliber earns from qualifying purchases. Tooling links above are affiliate links.

Methodology

What the calculator does

It looks up a published profile for the exact printer, resin, colour, layer height and (where published) temperature condition you select. It does not calculate exposure from multipliers, and it does not estimate settings for combinations without a published profile.

Value types

Nothing on this page is a measured value from your printer, and LayerCaliber has not physically print-tested these profiles.

Profile selection

Profiles come from resin manufacturers' own published settings. Each records the source URL, the date it was accessed, a profile version, and an evidence status. Sources used: ELEGOO Wiki resin settings and the Siraya Tech Blu user guide. Siraya Tech also publishes slicer profile files for many printers on its print settings download page.

Coverage

The ELEGOO profiles are extracted from the settings data published on the ELEGOO Wiki and checked value by value against it by script. Where ELEGOO lists separate print modes for a printer (for example "normal resin + fast printing"), each mode is a separate profile with its own layer height. ELEGOO's dental resins are not included: they are dental products outside the scope of this tool.

Science versus this tool

Photopolymer cure depth is commonly described by the Jacobs working curve, Cd = Dp · ln(E / Ec), where Dp and Ec are properties of a specific resin and E is the delivered dose. Those resin constants are not published for the consumer resins here, so this tool does not use the equation to compute settings. It is mentioned only to explain why settings are specific to each resin and light source.

Earlier versions

Before 19 October 2026 this site estimated exposure with generic multipliers (for example a 0.95× factor for 8K–14K screens, layer and temperature factors, and bottom exposure = normal × 10.5). Those multipliers were not supported by published sources and have been removed.

Calibration tests

Published settings are a starting point. Print a calibration test from its original creator and follow that creator's instructions for reading the result. LayerCaliber does not host or redistribute these files.

Record the result

Note the test, the exposure you used and what you changed. The "Record your calibrated values" panel keeps these in your browser and adds them to copied or printed settings.

Safety

The Safety Data Sheet (SDS) for your exact resin is the authority. Read it before use and follow its instructions where they differ from these general notes. ELEGOO publishes SDS documents on its resin SDS page; for other brands, ask the manufacturer or check the product page.

Skin and eyes

Uncured photopolymer resins commonly contain acrylates that can irritate skin and eyes and can cause skin sensitisation (allergy) with repeated contact. Wear the gloves and eye protection your SDS specifies, and replace gloves when they are contaminated or damaged.

Ventilation

Work in a well-ventilated area. Whether respiratory protection is needed, and of what type, depends on the resin, solvent and room. Follow the SDS and, for enclosed spaces, local occupational-safety guidance.

Solvents

Isopropyl alcohol (IPA) and similar wash solvents are flammable. Keep them away from ignition sources and store them closed and labelled.

Disposal

Do not pour resin or contaminated solvent down a drain. Disposal rules vary by location; check the SDS disposal section and your local hazardous-waste authority. Curing residue does not automatically make all remaining material suitable for ordinary household waste.

UV light

Do not look into an operating printer or cure station with the cover open. Keep covers closed while printing and curing.

If exposure occurs

Follow the first-aid section of the SDS for your resin and seek medical advice if symptoms persist.

These are general notes, not professional safety advice.

Privacy

Last updated: 22 October 2026

Calculator data

Your selections and any values you record are processed in your browser. The page sends no form submissions and no advertising requests. Recorded values and notes are never sent to analytics.

Analytics (only if you accept)

If you choose "Accept analytics" in the cookie notice, this site loads Google Analytics 4 (provided by Google) to count visits and see which pages and features are used. Google Analytics then sets first-party cookies (named _ga and _ga_<ID>) and receives information such as the pages you view, approximate location derived from your IP address, device and browser type, and the referring site. Google signals and ad personalisation are turned off. If you decline, or make no choice, Google Analytics is not loaded and no analytics cookies are set. You can change your choice at any time with "Cookie settings" at the bottom of the page. See how Google uses information from sites that use its services.

Saved in your browser

Your last selections and recorded values are stored in your browser's localStorage so the page reopens where you left off. Use "Reset to defaults" or clear this site's data in your browser to remove them. Your analytics choice is also stored there; change it with "Cookie settings".

Hosting

Like any website, loading this page sends ordinary requests to our web host, which may keep standard server logs (such as IP address, time and requested file). Fonts and images are served from this site. The only third-party script is Google Analytics, and it loads only after you accept analytics.

Shared links

"Share this configuration" creates a link containing only the selected profile (printer, resin, colour, condition). Recorded values and notes are never added to the link.

Third-party sites

Links to Amazon, manufacturers and calibration-test creators take you to sites with their own privacy policies.

This policy describes the current implementation and has not been reviewed by a lawyer.

Terms

Last updated: 19 October 2026

LayerCaliber shows starting settings copied from third-party manufacturer publications for educational use. They are not guaranteed to work on your printer. Results depend on things this site cannot see, including build-plate levelling, release-film condition and tension, light-source ageing, resin age and mixing, and room temperature.

Manufacturers may change their recommendations. Always check the cited source and run a calibration print before relying on any value.

No warranty

The site is provided "as is", without warranties of any kind.

Limitation of liability

To the extent permitted by law, LayerCaliber is not liable for failed prints, wasted material, equipment damage or other loss arising from use of this site.

These terms have not been reviewed by a lawyer. Seek qualified advice before relying on them.

Affiliate disclosure

Amazon Associates Program

LayerCaliber is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. As an Amazon Associate, LayerCaliber earns from qualifying purchases.

Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.

Which links

Links in "Related equipment" are Amazon search links tagged layercaliber-20. If you buy through one, we may earn a commission at no extra cost to you.

Endorsement statement

In line with the U.S. FTC's Guides Concerning the Use of Endorsements and Testimonials in Advertising (16 CFR Part 255), we disclose this financial relationship. LayerCaliber has not tested these products, and commissions do not influence any setting shown by the calculator. Search results are chosen by Amazon; check compatibility with your exact printer before buying.

Contact & calibration feedback

Spotted a profile that no longer matches its source, or want a printer and resin added? Include the source link if you have one.

contact@layercaliber.com

Open in mail app

Copy manually

Your browser blocked clipboard access. The text is selected below; press Ctrl+C (or Cmd+C) to copy it.